Plastering works in Bangalore – Plastering

Plastering works in Bangalore – Plastering

Plastering works in Bangalore : 

The word Plastering works in Bangalore or anywhere is used to define it is mortar cover smeared on the surface of walls and ceilings. The plaster not only eliminates the roughness of concrete or masonry surface but gives smooth and elegant required finishing. The plastering is used to prevent the entry of external water into the masonry surfaces. Fig 1.

Fig 1. External wall plastering works in Bangalore under progress

1. Requirements for good plaster :  

  1. It should stick to to the background and should stay during all deviations in the climatic conditions. (Fig. 2)
  2. Good plaster should be cost effective and economical.
  3. It should be hard and durable.
  4. Plaster should effectively protect the entry of moisture.
  5. It should retain good workability.
Fig 2. Internal wall plastering works in Bangalore under progress

Fig 2. Internal wall plastering works in Bangalore under progress

2. Common materials required for Plastering works in Bangalore:

Lime, Cement, Sand, Water and Admixture

3. Type of plastering :

The type of plaster can be classified based on the ingredient used and indent of finishes

a) Based on Ingredients

  1. Cement Plaster: It is the most frequently used Plastering works in Bangalore or for all construction works. If cement is used as a binding material then it is called cement plaster. Normally, it is to be applied in one coat only. The thickness of plaster coat is entirely depends on the practical conditions and type of building. For RCC surfaces, 1:3 CM for Ceilings and 1:4 CM for wall plastering with the thickness of 6 mm is highly advisable. This is the most suitable plaster used against dampness. ( Fig.3 )

    Fig 3: Cement Plastering works in Bangalore  for beams, columns and walls

  2. Lime Plaster: This is primarily a composition of sand, hydrated lime and water. If lime is used as a binding material then it is called lime plaster. Lime plaster’s mortar is usually prepared by mixing sand and lime in equal ratios. To get more strength for plaster, it is advisable to add little quantity off cement into it.(Fig. 4)

    Fig. 4 :  Lime Plastering works in Bangalore

  3. Cement lime plaster: Here little cement is added for lime plaster for obtaining smooth finishing surface.

b) Based on type of finish

1. Sand faced plaster: Normally sand face finishing is applicable for External Plastering works in Bangalore or anywhere. Here two coats of plastering is applied to get this finish.

  • First coat : For first coat, the CM in 1:4 ratio with 12 mm thick layer of cement sand mortar is applied and finished with rough coat by zigzag lines. It is then it is allowed for 7 days curing period.
  • Second Coat : After first coat the CM in 1:1 ratio with 8 mm thick layer of second coat with cement and sand is applied. After leveling, finish the surface using sponge.

The screened sand with uniform size is applied for walls using skimming float, the surface obtained now is called the sand faced plaster. (Fig. 1)

2. Pebble dash finish: In Pebble dash finish, the cement Mortar used should consist of combination of fine and coarse aggregate along with cement and sand with smooth work ability to apply for walls. (Fig. 5)

Fig 6: Pebble dash plaster finish

Fig 5: Pebble dash plastering works in Bangalore including its final finish

3. Rough cast finish: This is also known as spatter dash finish. Here the cement Mortar used should consist of coarse aggregate along with cement and sand with smooth work ability to apply for walls. (Fig. 6)

Fig 7: Rough cast Plaster finish

Fig 6: Rough cast Plastering works in Bangalore including its final finish

4. Smooth cast finish: To attain a smooth cast finish, the mortar used should be in the ratio 1: 3. After sieving the sand over 2.36 mm the passing sand below 2 mm obtained is called the Fine Sand is to be taken to prepare the mortar. For applying the cement mortar, use appropriate tool skimming float or wood float and finish the surface by smooth and even. (Fig.7)

Fig 8 : Smooth cast Plaster finish

Fig 7  : Smooth cast Plaster finish

5. Textured finish:

  • Texture plaster or Stucco plaster is decorative type of plaster which gives a brilliant finish for interior and exterior wall surfaces.
  • It is generally applied in three coats making the overall thickness of plaster to maximum 25 mm.
  • The first coat of thickness about 10 mm is called scratch coatis applied first the second coatis of thickness about 8 mm to 1o mm is applied as middle coat called fine coat or brown coat and the third coat of thickness 5 mm is applied as the final coat called white coat or finishing coat. (Fig.8)
Fig 9 : Texture Plaster Finish

Fig 8 : Texture Plaster Finish

c) Rough Guideline for proportion of mortar for plastering

  1. Internal ceiling CM 1:3
  2. Internal walls CM 1:6
  3. External walls CM 1:5

Plastering – 1: {Note: For Plastering Methodology and Procedure go through https://myhomemydesign.in/internal-plastering/ }

Plastering:

Types of plaster finishes:

Plastering application for wall:

TAGS :

Plaster, Plastering, External wall plastering, requirements of good plaster, internal plastering works, materials required for plastering, type of plastering, cement plaster, wall plastering, ceiling plastering, lime plaster, cement lime plaster, sand faced plaster, pebble dash finish, rough cast finish, smooth cast finish, textured finish.

STAY TUNED FOR MORE UPDATES….

One Comment

  1. admin
    May 02, 2019 at 5:03 am

    Know the complete details about Plastering, Requirements of Good Plastering and Different types of plastering works carried out in construction industry…

Leave a Comment

Your email address will not be published.